Menu

Discussion Forum

New Discussion
Filtra

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Frequency Domain Analysis of a Heat Transfer System

Posted 19 set 2011, 04:16 GMT-4 Heat Transfer & Phase Change Version 4.2 3 Replies

Jochen Zöllin
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello,
I am trying to determine the frequency response of a 2D heat transfer system to a harmonic heat source, but I can't seem to get the frequency domain study working with heat transfer physics.

My model so far is attached below. I have the geometry, materials, and physics set up and I have included the heat source to be varied harmonically. However, when I run the solver, only the initial conditions get returned and the solver reports solving for 0 degrees of freedom.

I am thinking this might be because the source term in the heat transfer equation is static, and does not vary harmonically. If this is the case, does anyone know how I can force this term to vary harmonically?

Otherwise, does anyone know how I should proceed?

Thanks for your time.

Attachments:

3 Replies Last Post 19 set 2011, 09:32 GMT-4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 19 set 2011, 05:45 GMT-4
Hi

but the thermal eqautions are not really that often developped as harmonic functions, so there could well be that the equations have not been written out in "harmonic form" (I do not have direct access t COMSOL just now, so I cannot check).

You can either use the time solver to see the time evolution, or if you are interested in the amplitudes, then you give a rms power level and you will get the stead sate rms values out. It all depends on the time constant of your model w.r.t your frequency.

Anyhow you do not get "waves" from the diffusion equations, as for the Maxwell equations

--
Good luck
Ivar
Hi but the thermal eqautions are not really that often developped as harmonic functions, so there could well be that the equations have not been written out in "harmonic form" (I do not have direct access t COMSOL just now, so I cannot check). You can either use the time solver to see the time evolution, or if you are interested in the amplitudes, then you give a rms power level and you will get the stead sate rms values out. It all depends on the time constant of your model w.r.t your frequency. Anyhow you do not get "waves" from the diffusion equations, as for the Maxwell equations -- Good luck Ivar
Jochen Zöllin
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 19 set 2011, 07:58 GMT-4
Thanks for your reply,

I am using the heat transfer model as an analogy for squeeze-film damping in micro-structures (pressure = temperature, plate normal velocity = heat source). I would like to extract the damping pressure and squeeze-stiffness pressure, (real temperature and imaginary temperature in the heat transfer analogy), at various frequencies.

I can do this using a time response analysis, but it requires much more solver time than I would like, as it takes a while for the transients to die out. As for using a power-based approach, I don't think I will be able to separate the real and imaginary responses.

A harmonic analysis, therefore, would be ideal. Is there no way that I can make it work?

Cheers,
Jochen
Thanks for your reply, I am using the heat transfer model as an analogy for squeeze-film damping in micro-structures (pressure = temperature, plate normal velocity = heat source). I would like to extract the damping pressure and squeeze-stiffness pressure, (real temperature and imaginary temperature in the heat transfer analogy), at various frequencies. I can do this using a time response analysis, but it requires much more solver time than I would like, as it takes a while for the transients to die out. As for using a power-based approach, I don't think I will be able to separate the real and imaginary responses. A harmonic analysis, therefore, would be ideal. Is there no way that I can make it work? Cheers, Jochen
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 19 set 2011, 09:32 GMT-4
Hi

you would need to rewrite the equations I believe using the math PDE and creating a harmonic development of the math diffusion equations,
Not sure where to start as I have become lazy with the latest COMSOL versions and manange to use the predefined physics for all my problems ;)

--
Good luck
Ivar
Hi you would need to rewrite the equations I believe using the math PDE and creating a harmonic development of the math diffusion equations, Not sure where to start as I have become lazy with the latest COMSOL versions and manange to use the predefined physics for all my problems ;) -- Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content