Menu

Discussion Forum

New Discussion
Filtra

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

how to find the x,y,z axis displacement

Posted 25 set 2011, 20:35 GMT-4 Version 4.2a 4 Replies

Anis Nurashikin Nordin
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi,

I have question regarding about on how to find the x,y,z axis displacement.
Currently I'm using Comsol 4.2 and attached are the file of my result. Is it correct because i'm quite confius about the result. Can everyone verify my result?

Regards
Anwar
4 Replies Last Post 9 lug 2012, 12:58 GMT-4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 26 set 2011, 01:53 GMT-4
Hi

because of the large displacement values for the eigenmode analysis ?

If so, reread the theory around eigenmode analysis:
You will then notice that amplitudes are not restrained, one can only get:
1) frequencies,
2) relative shapes
3) if you chose the correct normalisation, relative mode energy comparison.

But you never get any absolute displacement values.

I believe that the COMSOL developpers have left this feature (normalisation) this way as the default to REMIND all users about this effect. (at least for those noticing the large displacements and then ask themselves the question why )

--
Good luck
Ivar
Hi because of the large displacement values for the eigenmode analysis ? If so, reread the theory around eigenmode analysis: You will then notice that amplitudes are not restrained, one can only get: 1) frequencies, 2) relative shapes 3) if you chose the correct normalisation, relative mode energy comparison. But you never get any absolute displacement values. I believe that the COMSOL developpers have left this feature (normalisation) this way as the default to REMIND all users about this effect. (at least for those noticing the large displacements and then ask themselves the question why ) -- Good luck Ivar
Ananiah Durai Sundararajan
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 3 mag 2012, 00:47 GMT-4
Hi Anis,
saw your model, I am trying to do displacement analysis for a pressure sensor, please tell me the procedure how u did it?
Hi Anis, saw your model, I am trying to do displacement analysis for a pressure sensor, please tell me the procedure how u did it?
Anis Nordin
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 3 mag 2012, 01:38 GMT-4

Hi Anis,
saw your model, I am trying to do displacement analysis for a pressure sensor, please tell me the procedure how u did it?


Hi Ananiah Durai Sundararajan,

basically, can you explain more about your model.Kindly, to do the displacement analysis we must put the
model in air condition and some physical configuration such as fix constraint, linear elastic material.

Regards.
[QUOTE] Hi Anis, saw your model, I am trying to do displacement analysis for a pressure sensor, please tell me the procedure how u did it? [/QUOTE] Hi Ananiah Durai Sundararajan, basically, can you explain more about your model.Kindly, to do the displacement analysis we must put the model in air condition and some physical configuration such as fix constraint, linear elastic material. Regards.
Guillermo Andrés Borrero Becerra
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 9 lug 2012, 12:58 GMT-4
Hi Ananiah Durai Sundararajan

I am modeling a SAW sensor for pressure measurement. And I also have to do a displacement analysis. Please can you send me your pressure sensor model?. I really appreciate your help.
Hi Ananiah Durai Sundararajan I am modeling a SAW sensor for pressure measurement. And I also have to do a displacement analysis. Please can you send me your pressure sensor model?. I really appreciate your help.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content