Menu

Discussion Forum

New Discussion
Filtra

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Fluid Structure Interaction

Posted 11 giu 2020, 23:55 GMT-4 Structural & Acoustics, Fluid & Heat, Structural Mechanics Version 5.5 4 Replies

Mugdha Patel
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Im trying to model a fluid entering the eye. This is modelled as a fluid being injected between 2 layers. There is an inlet but there is not supposed to be an outlet as the fluid should enter in and disperse between the layers. My model fails to reach consistent values, however. Any help would be very much appreciated.

Thank you

Attachments:

4 Replies Last Post 14 giu 2020, 13:24 GMT-4
Aniket Jayawant
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 13 giu 2020, 11:52 GMT-4

Hello Mugdha, You were missing a pressure point constant which I have added. Also, your values on the inlet should be either mass controlled or velocity controlled. Use really small values as I have done as the volume inside the computation exceeds the pressure limit resulting in chocking the system. The time settings were also too large; try reducung them a little. Good Luck

Hello Mugdha, You were missing a pressure point constant which I have added. Also, your values on the inlet should be either mass controlled or velocity controlled. Use really small values as I have done as the volume inside the computation exceeds the pressure limit resulting in chocking the system. The time settings were also too large; try reducung them a little. Good Luck
Mugdha Patel
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 13 giu 2020, 12:13 GMT-4

Hello Mugdha, You were missing a pressure point constant which I have added. Also, your values on the inlet should be either mass controlled or velocity controlled. Use really small values as I have done as the volume inside the computation exceeds the pressure limit resulting in chocking the system. The time settings were also too large; try reducung them a little. Good Luck

Thank you so much for the feedback! I really appreciate it. I will try implementing these solutions.

>Hello Mugdha, >You were missing a pressure point constant which I have added. >Also, your values on the inlet should be either mass controlled or velocity controlled. >Use really small values as I have done as the volume inside the computation exceeds the pressure limit resulting in chocking the system. >The time settings were also too large; try reducung them a little. >Good Luck Thank you so much for the feedback! I really appreciate it. I will try implementing these solutions.
Aniket Jayawant
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 13 giu 2020, 12:32 GMT-4

Here you go.

Here you go.

Attachments:

Mugdha Patel
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 4 years ago 14 giu 2020, 13:24 GMT-4

With your model I am getting this error: Recoverable error in residual, but solver could not recover. Time: 0.0064000000000000003 s. Last time step is not converged.

Were you able to get a solution?

I will update if I find a solution. Thank you

With your model I am getting this error: Recoverable error in residual, but solver could not recover. Time: 0.0064000000000000003 s. Last time step is not converged. Were you able to get a solution? I will update if I find a solution. Thank you

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content