Menu

Discussion Forum

New Discussion
Filtra

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Modeling packed bed reactor

Posted 7 gen 2011, 09:52 GMT-5 Fluid & Heat, Computational Fluid Dynamics (CFD), Chemical Reaction Engineering, Geometry Version 4.0 3 Replies

Chung-Yul Yoo
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hi

I am a beginner of COMSOL. I would like to design packed-bed reactor. The reactor diameter is 1 mm, and the particle size is about 1 micro meter. The porosity of packed bed is about 60%. If I want to fill reactor with this small particle, I need about 1000 particles, it take too long time for me. Is it possible to mimic this reactor using other method?

Thank you for your help

3 Replies Last Post 8 dic 2013, 16:43 GMT-5
COMSOL Moderator

Hello Chung-Yul Yoo

Your Discussion has gone 30 days without a reply. If you still need help with COMSOL and have an on-subscription license, please visit our Support Center for help.

If you do not hold an on-subscription license, you may find an answer in another Discussion or in the Knowledge Base.

Sanjeev Rao
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 17 feb 2011, 12:40 GMT-5
There is a Packed Bed reactor model in the Chemical Engineering Model library, in version 3.5a (not sure about 4.0 because haven't used it). You do not have to physically insert 1000 particles in the geometry, there are ways around it; the model file explains it in detail. Use the model documentation to work along with the file.

Hope this helps!

There is a Packed Bed reactor model in the Chemical Engineering Model library, in version 3.5a (not sure about 4.0 because haven't used it). You do not have to physically insert 1000 particles in the geometry, there are ways around it; the model file explains it in detail. Use the model documentation to work along with the file. Hope this helps!
Adel Shojaei
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 17 apr 2011, 06:29 GMT-4
hi dear
I am working with this software and I am beginner and working about reactors.
I'm student of petrochemical engineering.
can you send me some examples about fixed bed rectors?
If you don't have any example about fixed bed reactors please sent me some useful and simple examples about reactors.
thanks
hi dear I am working with this software and I am beginner and working about reactors. I'm student of petrochemical engineering. can you send me some examples about fixed bed rectors? If you don't have any example about fixed bed reactors please sent me some useful and simple examples about reactors. thanks
Moien Bahardoost
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 8 dic 2013, 16:43 GMT-5

There is a Packed Bed reactor model in the Chemical Engineering Model library, in version 3.5a (not sure about 4.0 because haven't used it). You do not have to physically insert 1000 particles in the geometry, there are ways around it; the model file explains it in detail. Use the model documentation to work along with the file.

Hope this helps!


There are so many ambiguous points in this model,
Could you please tell me about the definition of geometry and implication of two models (mod1 & mod2)?
I think the “general Extrusion” is the critical point that I can’t follow.
I would be grateful if you could introduce me any references through which I understand this intricate modeling.
[QUOTE] There is a Packed Bed reactor model in the Chemical Engineering Model library, in version 3.5a (not sure about 4.0 because haven't used it). You do not have to physically insert 1000 particles in the geometry, there are ways around it; the model file explains it in detail. Use the model documentation to work along with the file. Hope this helps! [/QUOTE] There are so many ambiguous points in this model, Could you please tell me about the definition of geometry and implication of two models (mod1 & mod2)? I think the “general Extrusion” is the critical point that I can’t follow. I would be grateful if you could introduce me any references through which I understand this intricate modeling.

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content