Menu

Discussion Forum

New Discussion
Filtra

Note: This discussion is about an older version of the COMSOL Multiphysics® software. The information provided may be out of date.

Discussion Closed This discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one, click here.

Interior boundary v4.1

Posted 28 set 2011, 12:21 GMT-4 Version 4.1 3 Replies

Cheng Chen
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello folks

I'm using the laminar flow & heat transfer physics in COMSOL 4.1, trying to solve problems such as microchannel flow and convective heat transfer. To simplify the model, I want to change the type of an interior boundary, from solid-fluid interface (wall) to an open boundary (outlet). But I cannot find any option to define or change the interior boundaries.

I understand that physically this boundary is unreasonable. But I noticed that COMSOL 3.5a has the option to change the type or equations of interior boundaries. I wonder if this function is eleminated in version 4s or just works in a different way?

Does anyone have similar experience with version 4.1 on these issues? Really appreciate if someone could help me figure this out.

Thank you.
Cheng
3 Replies Last Post 29 set 2011, 11:09 GMT-4
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 28 set 2011, 15:00 GMT-4
Hi

I have hear that v4 has been deigned to accept less "non physical" BC's, so perhaps you have hit one of these. If so there mustbe another way to express your BC, to make it physical. the results would probably be cleaner too, no ? ;)

--
Good luck
Ivar
Hi I have hear that v4 has been deigned to accept less "non physical" BC's, so perhaps you have hit one of these. If so there mustbe another way to express your BC, to make it physical. the results would probably be cleaner too, no ? ;) -- Good luck Ivar
Cheng Chen
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 29 set 2011, 11:05 GMT-4
Hi Ivar, thanks for your advice. But I didn't get the exact idea of "another way". Do you mean I shall modify the model/geometry to make it physical? Or COMSOL 4 has other methods to modify these "non-physical" boundaries?

Thank you.
Cheng
Hi Ivar, thanks for your advice. But I didn't get the exact idea of "another way". Do you mean I shall modify the model/geometry to make it physical? Or COMSOL 4 has other methods to modify these "non-physical" boundaries? Thank you. Cheng
Ivar KJELBERG COMSOL Multiphysics(r) fan, retired, former "Senior Expert" at CSEM SA (CH)
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 1 decade ago 29 set 2011, 11:09 GMT-4
Hi

I mean you must add the PDEs by hand for the specific boundaries, that is the only way to get around COMSOL physics, if you want to go "non physical".

But I would anyhow advice to rethink over the issue and see if there is not a better, respecting fully the physics way ,of doing things

--
Good luck
Ivar
Hi I mean you must add the PDEs by hand for the specific boundaries, that is the only way to get around COMSOL physics, if you want to go "non physical". But I would anyhow advice to rethink over the issue and see if there is not a better, respecting fully the physics way ,of doing things -- Good luck Ivar

Note that while COMSOL employees may participate in the discussion forum, COMSOL® software users who are on-subscription should submit their questions via the Support Center for a more comprehensive response from the Technical Support team.

Suggested Content